Learning how to snake a toilet will help you to fix any clog in your toilet. This process will remove the obstruction, leaving the toilet free of matter. This matter can be hazardous or dirty, so you’ll need to dispose of it properly. To avoid any injuries while snaking, you may want to use a container to catch the debris.
Unclog a toilet with a snake
A toilet snake is an effective way to unclog a clogged toilet. This tool has a metal coil on its head that can be pushed down the drain. The metal wire is covered with plastic to avoid damaging the porcelain. After you have placed the snake in the toilet, turn the handle of the snake until the metal coil comes out of the toilet and is firmly in contact with the handle. Once the snake has reached the clogged area, pull the handle slowly.
Using the right snake can make the process easier. The snake’s head must be angled down towards the drain. Alternatively, you can add a drain cleaner to the bowl and let it sit for 15 to 30 minutes. You can also add hot water that contains a mixture of vinegar and dish soap. If the snake cannot turn the clog, it’s most likely because of pipe corrosion, a clog, or excessive force.
If you don’t have a snake or aren’t comfortable using a snake, you can use a wire coat hanger. It’s lightweight and metallic, making it a good alternative to a plunger. The only drawback to using a coat hanger to unclog a toilet is that it may damage the porcelain of the toilet. The best way to use a snake is to buy a toilet snake specially designed for this task.
Unclog a toilet with a plunger
One of the easiest ways to unclog a toilet is to use a plunger. A plunger that has a flange works best. Simply place the plunger in the toilet bowl and push down on it. It is important to push gently, as pushing too hard could splash dirty water all over you.
Be sure to remove all debris from the toilet bowl before you begin. To do this, make sure the plunger has enough water in it. Tip the plunger head slightly toward the water surface. This will force air out of the plunger, creating big bubbles. Once the water has reached the water level that is required, use the plunger to clear the drain opening. Then, make several quick pushes and pulls until the water is gone.
If the plunger doesn’t clear the clog, try using a wire coat hanger to flush it. It is important to wear disposable gloves to protect your skin, and wrap the wire end with duct tape to avoid scratching the toilet. Push the hanger in circular motions down the pipe until you feel it hitting the obstruction.
Another option is to use a chemical solution. These can be dangerous if used improperly and may cause an explosion or noxious fumes. Be careful not to mix household chemicals. Liquid-Plumr and Drano can both be harmful to people and pipes. A safer way to unclog a toilet is to pour hot water and soap in it.
Unclog a toilet with an auger
An auger works by snaking the toilet’s drain. It will not remove the clog completely, but it can break it up into small pieces so that you can flush the toilet. Once you’ve snaked the drain, be sure to empty the water from the toilet tank. It’s important to wear gloves to protect your hands during this process. Afterwards, you should flush the toilet to check if it’s clear.
To start, push the auger cable down through the toilet trap. When the cable reaches its full extension, turn the handle a couple of times backward to ensure the cable gets through the clog. You should be able to feel resistance in the cable as the auger moves through the toilet. Repeat the process until the clog has been removed.
Before you use an auger, it is important to wear gloves. Once you have the gloves on, turn off the water supply. Then, put on a pair of rubber gloves. Next, place a large empty bucket next to the toilet. Aim the auger’s cable towards the drain in the back. Next, turn the handle clockwise to release the cable and extend it down the pipe.
For stubborn clogs, an auger is an excellent solution. It can reach the top of the drain and break through the clog. Just be sure to read the instructions before starting the process. You should always wear eye protection and work gloves.
